LEARNING THE BASICS OF INSTALLING A BATHTUB

Learning the Basics of Installing a Bathtub

Learning the Basics of Installing a Bathtub

Blog Article

Call

How do you actually feel on the subject of A Step-by-Step Guide to Installing a Bathtub?


Tools You Need to Install a New Bathtub
Setting up a tub isn't exactly rocket science, however it does require solid plumbing, woodworking, and also occasionally, tiling skills. Replacing an old bath tub with a brand-new one is also a moderately challenging job. If the old tub is easily accessible, the job can move speedily; if you have to open up a wall to remove the old bathtub and also place the new bathtub, the task is a lot harder. In either instance, the job is within a residence handyman's skills, although you will certainly need an assistant to vacate the old bathtub as well as embeded in the brand-new one. Ensure you have qualified on your own for the task and fit attempting it. As opposed to employing a specialist to take control of a halfway-completed job, it is far better to think about using one prior to you start. Opportunities are you may require an expert plumber to make tube connections.
This write-up will help you mount a new bathtub in your washroom if you have currently purchased a new tub as well as do not require to transform the setup of your previous water system pipelines.
Your tools and material list ought to comprise the following:
  • New Tub
  • Hammer

  • Pipe Wrenches

  • Prybar

  • Safety Glasses

  • Degree

  • Pliers

  • Adjustable Wrench

  • Putty Blade

  • Screwdriver

  • Cold Chisel

  • Tape Measure

  • Pipe Caps


  • Planning for the Setup


    To start with, the supporting frame provided with the bathroom must be fitted (if called for) according to the supplier's directions. Next off, fit the taps or mixer to the tub. When fitting the tap block, it is very important to ensure that if the faucet comes with a plastic washer, it is fitted in between the bath and also the faucets. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the faucets system to stop strain on the bath tub.
    Fit the versatile faucet adapters to the bottom of the two taps utilizing 2 nuts as well as olives (often provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet through the hole in the bath. Make use of the nut provided by the manufacturer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
    Next off, fit completion of the flexible overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. Ensure you make use of all of the supplied washing machines.
    Connect the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Link all-time low of the overflow tube in a similar manner.The bath should currently prepare to be fitted in its final setting.

    Removing Old Touches


    If you require to change old taps with brand-new ones as a part of your installation, then the first thing you need to do is detach the water. After doing so, activate the faucets to drain pipes any kind of water continuing to be in the system. The procedure of removing the existing taps can be quite bothersome as a result of the restricted access that is frequently the instance.
    Utilize a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that connects the supply pipelines to the faucets. Have a fabric prepared for the staying water that will certainly originate from the pipes. As soon as the supply pipes have been gotten rid of, use the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary taps from transforming during this procedure. As soon as the faucets have actually been eliminated, the holes in the bath/basin will need to be cleaned of any kind of old securing substance.
    Before going on to fit the brand-new faucets, compare the pipe connections on the old faucets to the new taps. If the old faucets are longer than the new faucets, after that a shank adapter is needed for the new faucets to fit.

    Mounting the Bath tub


    Using the two wood boards under its feet, position the bath tub in the required position. The wood boards are valuable in equally spreading out the weight of the bathtub over the location of the boards instead of focusing all the weight onto 4 small points.
    The next objective is to make sure that the bath tub is leveled all round. This can be achieved by inspecting the level and readjusting the feet on the bathtub up until the level reviews level.
    To mount faucets, fit all-time low of the furthest adaptable faucet port to the proper supply pipe by making a compression sign up with; then do the same for the other faucet.
    Turn on the supply of water as well as inspect all joints and brand-new pipework for leaks and tighten them if required. Load the tub and also examine the overflow electrical outlet and the typical electrical outlet for leakages.
    Finally, fix the bathroom paneling as described in the maker's user's manual. Tiling as well as sealing around the bathtub needs to wait up until the tub has actually been utilized at least when as this will certainly resolve it into its last setting.

    Suitable New Taps


    If the tails of the new faucets are plastic, then you will require a plastic connector to stop damages to the thread. One end of the connector fits on the plastic tail of the tap as well as the other end offers a link to the existing supply pipes.
    If you need to fit a monobloc, after that you will call for decreasing couplers, which attaches the 10mm pipe of the monobloc to the typical 15mm supply pipeline.
    Next, place the tap in the installing opening in the bath/basin ensuring that the washers are in location in between the tap as well as the sink. Safeguard the tap in place with the producer provided backnut. As soon as the tap is firmly in position, the supply pipelines can be linked to the tails of the taps. The taps can either be connected by utilizing corrugated copper piping or with normal tap adapters. The former type should be connected to the faucet finishes first, tightening only by hand. The supply pipelines can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been connected.

    Tiling Around the Bath tub


    In the area where the bath meets the ceramic tile, it is necessary to seal the joins with a silicone rubber caulking. This is essential as the fitting can move enough to crack a stiff seal, triggering the water to permeate the wall surface in between the bath as well as the tiling, leading to difficulties with dampness and feasible leaks to the ceiling listed below.
    You can pick from a selection of coloured sealers to assimilate your components and also installations. They are marketed in tubes and also cartridges, and also are capable of securing voids as much as a width of 3mm (1/8 inch). If you have a larger space to fill, you can load it with spins of soaked newspaper or soft rope. Keep in mind to constantly fill the bath tub with water prior to securing, to allow for the activity experienced when the tub remains in use. The sealer can crack rather very early if you do not take into consideration this motion prior to sealing.
    Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are additionally quickly readily available on the marketplace. It is advisable to fit the tiles using water-resistant or waterproof adhesive as well as cement.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    A Step-by-Step Guide to Installing a Bathtub

    I hope you enjoyed reading our topic about How to Install a Bathtub. Thanks a ton for taking time to read our piece of content. Enjoyed reading our piece? Please share it. Help someone else discover it. I praise you for your time. Visit again soon.


    Stay calm, just ring.

    Report this page